Anuchlor - MIO : Chlorinated Rubber Micaceous Iron Oxide  


Product Description :


Anuchlor - MIO is a high performance high build chlorinated rubber based coating pigmented with micaceous iron oxide (MIO) pigment. MIO is a lamellar plate-like pigment that forms a thick lustrous layer after application. As the coating dries, the very thin platelet shaped pigment particles orient themselves parallel to the substrate to give an armoured effect to the film and also act as an impediment to the diffusion of oxygen and moisture through the film. It is ideal for use in marine and chemical environments.

Features and Benefits :

Easy to apply and can be applied via airless spray, conventional spray and brush.

Can be used as primer, intermediate or finish coat.

Renders hard, inert film showing excellent resistance towards dilute acids, alkalis, certain salts, oxidizing agents, aliphatic hydrocarbons, alcohols, mineral oils, greases etc.

Has very high resistance to permeability of water, moisture, oxygen and other atmospheric pollutants.

Suitable for varied end applications i.e. ideal for high humidity, moisture, marine atmospheres, heavy rains, high temperatures, damp conditions, very dusty and fungus prone conditions.

Impart excellent inter-coat adhesion properties.

Extremely durable and weather resistant.

Non-toxic and cost-effective.


Recommended uses :


Fertilizer plants

Sewage farms

Concrete Storage Tanks

Water Treatment Plants

Structural Steel

Galvanized Iron

Bleacheries and laundries


Pulp and Paper Mills

Chemical Plants

Marine and shore installations

Swimming Pools

Food Processing Plants

Areas of excessive moisture

Petro-chemical Plants


  Surface Preparation :  

Steel - The surface should be blast cleaned to SSPC-SP 10-63T or NACE No. 2 i.e. loose rust and scales, dirt, grease, oil, paint, wax, weak oxide films and other contaminants should be removed. It means that at least 95% of any given square inch has the appearance of white metal and the remainder is limited to slight discolourations. Blast cleaning to SSPC-SP 5-63 or NACE No. 1 is recommended where heavy corrosive conditions exist. That means a surface with a grey metallic colour, slightly roughened to form a suitable anchor pattern for coatings. This surface is free of all oil, grease, dirt, mill scale, rust, corrosion products, oxides, paint and other foreign matter. In absence of blast cleaning, prepare the metal surface by wire brushing, sanding, grinding, scrapping or chipping with hand or power tools. Remove all the contaminants. Apply one or two coats of Anuchlor CZP 500 primer. Then apply a coat of Anuchlor - MIO followed by 2-3 coats of Anuchlor 555 LB Chlorinated Rubber Enamel.

Galvanized Iron - Remove dirt, dust, oil, old paint etc. Degrease the surface with degreasing solvents like xylene or tri-chloroethylene. Apply one coat of Anuprime - 291 Wash Primer for obtaining maximum adhesion. Apply one coat of Anuchlor CZP 500 primer. Then apply a coat of Anuchlor - MIO followed by 2-3 coats of Anuchlor 555 LB.





Anuchlor - MIO


Single pack cold cured


Chlorinated rubber / MIO


Brownish Grey


Smooth and Matt

Volume Solids

45± 3%

Dry film thickness per coat

65 to 75 microns

Coverage-(theoretical-no loss)

6.9 to 6 m² /litre

Serviceability @ 30° C

- Dry to touch

- Re-coat by Spray

- Re-coat by Brush

- Full Cure


30 - 45 minutes

3-4 hours

16 -24 hours

7 days

Relative Humidity


Application Temperature

- minimum

- maximum


4° C

35° C

Dry heat resistance

65° C


Anusol - CRT Thinner

Flash Point

25° C


4 & 20 litres

Shelf Life

6 months


Flammable. Keep away from heat and open flame. Maintain good ventilation and avoid breathing vapours.


Product Limitation :

Anuchlor - MIO is not resistant to most solvents, animal and vegetable oils and fats common in dairies, packinghouses and sewage treatment facilities.
Do not use on floors.
Epoxy and polyurethane topcoats are not suitable.
Notes :-  
Brushes and spray equipments should be cleaned with Anusol - CRT Thinner.
The contents should be stirred thoroughly prior to use.
When overcoating the weathered or aged Anuchlor - MIO, ensure that the coating is fully free from all contamination such as oil, dust, grease, stains etc.
This coating should always be thinned with Anusol - CRT Thinner. The use of alternative thinners can severely inhibit the curing mechanism of the coating.

Disclaimer :-


Information provided herein is based upon tests believed to be reliable. It does not guarantee the results to be obtained. Nor does it make any express and implied warranty or merchantability, or fitness for a particular purpose concerning the effects or results of such case. It does not release you from the obligation to test the products supplied by us as to their suitability for the intended uses. The application, surface preparation and use of the products are beyond our control and, therefore, entirely your own responsibility.

Download as PDF format
Top side


View site-map Home page About us Search View products View our services Add your feedback View contact us Click to go top position Click to Download pdf